search
Confirm
Cancel
Language
Where are you now:
Homepage
>
>
>
How to make the bar code printer in the label paper normal use

How to make the bar code printer in the label paper normal use

  • Categories:Industry News
  • Author:
  • Origin:
  • Time of issue:2022-07-11
  • Views:0

(Summary description)

How to make the bar code printer in the label paper normal use

(Summary description)

  • Categories:Industry News
  • Author:
  • Origin:
  • Time of issue:2022-07-11
  • Views:0
Information

1. Wrap the out paper around the recycling rod, remove the fixing fork, roll the paper tightly, and then insert it along the slot to fix it. Finally, adjust the label paper location and width, with the hand to press the print head, if there is no pressure to print head, boot after "flute, flute, flute" the printer, if the printer doesn't work or out of the paper is not normal, that the print head there is no pressure in place, if the print label paper, photosensitive sensor under the print head think ahead for a period of no label paper automatically, Until the label is in place.

2, boot, the first time to print, should be bar code printer to try a, print correct rear. If there is a problem should continue to try to type a few, try to use the same type of printing paper when printing, otherwise it must be reset debugging. If the label paper is not removed after printing, the second print content paper will not come out, you must remove the previous label paper, the second can be printed.

3. Take TSC label printer as an example. If you enter automatic file, the printer will print out page by page according to the time interval set. If the previous label is not removed, the latter label cannot be printed. However, bar code printing pricing scale is still in accordance with the specified time to continue to send out the print content, send out all the content of the print will stop, or power reset after printing.

4. When the ambient temperature is about 70oC, the printing paper will fade, so special attention should be paid to the influence of the ambient temperature, humidity and light.

5. Bar code scale must set the length and width of the label paper. If the setting is not appropriate, it will be a mistake.

6, the maximum print width is less than the maximum paper width 58mm.

7. When loading the label tube, first push the upper end of the right cover inward and then let go, the side cover will automatically pop up. Then take out the supporting rod of the paper cylinder and pull it out in parallel. Incline into the direction, and then insert the paper cylinder support rod, the bottom of the support rod along the groove slide into.

8. Then move the vertical lever of the print head, the print head will automatically tilt up, pull out the label paper from the gap under the print head, and then wind back down. Notice that there is a sensor (black) under the print head, and there is also a sensor under the print head. Avoid the sensor and do not wrap the sensor in the label. If the printer sounds "flute" "flute" "flute" alarm after the machine is turned on, it means that the paper is not installed properly. Reload the paper as required.

 

Scan the QR code to read on your phone

NEWS

Superstrong Resin Thermal Transfer Ribbon for Barcode Label Printer 30mm-110mm*300m
Superstrong Resin Thermal Transfer Ribbon for Barcode Label Printer 30mm-110mm*300m
Resin Thermal Transfer Ribbon for Barcode Label Printer
Resin Thermal Transfer Ribbon for Barcode Label Printer
Resin Barcode Carbon Thermal Ribbon
Resin Barcode Carbon Thermal Ribbon
Messages
Close
code

Shantou high tech zone jusheng technology Co.Ltd

E-mail:chisheng@barcode.cn

Tel: 86 754 88461930
Wechat official account : KRUBO-CISON
Add:15/F,WeiGao Building,NO.2,Keji East Road,GaoXin Zone, Shantou City, Guangdong Province

Copyright © Shantou high tech zone jusheng technology Co.Ltd.  All Rights Reserved   粤ICP备05059720号   Powered by:www.300.cn  SEO tags

Wechat official account